1233.0 - Australian Harmonized Export Commodity Classification (AHECC), Jan 2006  
ARCHIVED ISSUE Released at 11:30 AM (CANBERRA TIME) 17/06/2003   
   Page tools: Print Print Page  


Sub-Chapter I

Primary materials; products in granular or powder form
      7201
Pig iron and spiegeleisen in pigs, blocks or other primary forms
      7202
Ferro-alloys
      7203
Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99.94%, in lumps, pellets or similar forms

      7204
Ferrous waste and scrap; remelting scrap ingots of iron or steel
      7205
Granules and powders, of pig iron, spiegeleisen, iron or steel

Sub-Chapter II

Iron and non-alloy steel
      7206
Iron and non-alloy steel in ingots or other primary forms (excluding iron of 7203)
      7207
Semi-finished products of iron or non-alloy steel
      7208
Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, hot-rolled, not clad, plated or coated
      7209
Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, cold-rolled (cold-reduced), not clad, plated or coated
      7210
Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, clad, plated or coated
      7211
Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, not clad, plated or coated
      7212
Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, clad, plated or coated
      7213
Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel
      7214
Other bars and rods of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but including those twisted after rolling

      7215
Other bars and rods of iron or non-alloy steel
      7216
Angles, shapes and sections of iron or non-alloy steel
      7217
Wire of iron or non-alloy steel

Sub-Chapter III

Stainless Steel
      7218
Stainless steel in ingots or other primary forms; semi-finished products of stainless steel
      7219
Flat-rolled products of stainless steel, of a width of 600 mm or more
      7220
Flat-rolled products of stainless steel, of a width of less than 600 mm
      7221
Bars and rods, hot-rolled, in irregularly wound coils, of stainless steel
      7222
Other bars and rods of stainless steel; angles, shapes and sections of stainless steel
      7223
Wire of stainless steel

Sub-Chapter IV

Other alloy steel; hollow drill barsand rods, of alloy or non-alloy steel
      7224
Other alloy steel in ingots or other primary forms; semi-finished products of other alloy steel
      7225
Flat-rolled products of other alloy steel, of a width of 600 mm or more
      7226
Flat-rolled products of other alloy steel, of a width of less than 600 mm
      7227
Bars and rods, hot-rolled, in irregularly wound coils, of other alloy steel
      7228
Other bars and rods of other alloy steel; angles, shapes and sections, of other alloy steel; hollow drill bars and rods, of alloy or non-alloy steel

      7229
Wire of other alloy steel


NOTES

1. In this Chapter and, in the case of Notes (d), (e) and (f) throughout this Classification, the following have the meanings hereby assigned to them:
    (a) Pig iron
      Iron-carbon alloys not usefully malleable, containing more than 2% by weight of carbon and which may contain by weight one or more other elements within the following limits;
      - not more than 10% of chromium
      - not more than 6% of manganese
      - not more than 3% of phosphorus
      - not more than 8% of silicon
      - a total of not more than 10% of other elements.
      (b) Spiegeleisen
      Iron-carbon alloys containing by weight more than 6% but not more than 30% of manganese and otherwise conforming to the specification at (a) above.
      (c) Ferro-alloys
      Alloys in pigs, blocks, lumps or similar primary forms, in forms obtained by continuous casting and also in granular or powder forms, whether or not agglomerated, commonly used as an additive in the manufacture of other alloys or as de-oxidants, de-sulphurising agents or for similar uses in ferrous metallurgy and generally not usefully malleable, containing by weight 4% or more of the element iron and one or more of the following:
      - more than 10% of chromium
      - more than 30% of manganese
      - more than 3% of phosphorus
      - more than 8% of silicon
      - a total of more than 10% of other elements, excluding carbon, subject to a maximum content of 10% in the case of copper.
      (d) Steel
      Ferrous materials other than those of 7203 which (with the exception of certain types produced in the form of castings) are usefully malleable and which contain by weight 2% or less of carbon.However, chromium steels may contain higher proportions of carbon.
      (e) Stainless steel
      Alloy steels containing, by weight, 1.2% or less of carbon and 10.5% or more of chromium, with or without other elements.
      (f) Other alloy steel
      Steels not complying with the definition of stainless steel and containing by weight one or more of the following elements in the proportion shown:
      - 0.3% or more of aluminium
      - 0.0008% or more of boron
      - 0.3% or more of chromium
      - 0.3% or more of cobalt
      - 0.4% or more of copper
      - 0.4% or more of lead
      - 1.65% or more of manganese
      - 0.08% or more of molybdenum
      - 0.3% or more of nickel
      - 0.06% or more of niobium
      - 0.6% or more of silicon
      - 0.05% or more of titanium
      - 0.3% or more of tungsten (wolfram)
      - 0.1% or more of vanadium
      - 0.05% or more of zirconium
      - 0.1% or more of other elements (except sulphur, phosphorus, carbon and nitrogen), taken separately.
      (g) Remelting scrap ingots of iron or steel
      Products roughly cast in the form of ingots without feeder-heads or hot tops, or of pigs, having obvious surface faults and not complying with the chemical composition of pig iron, spiegeleisen or ferro-alloys.
      (h) Granules
      Products of which less than 90% by weight passes through a sieve with a mesh aperture of 1 mm and of which 90% or more by weight passes through a sieve with a mesh aperture of 5 mm.
      (ij) Semi-finished products
      Continuous cast products of solid section, whether or not subjected to primary hot-rolling; and
      Other products of solid section, which have not been further worked than subjected to primary hot-rolling or roughly shaped by forging, including blanks for angles, shapes or sections.
      These products are not presented in coils.
      (k) Flat-rolled products
      Rolled products of solid rectangular (other than square) cross-section, which do not conform to the definition at (ij) above in the form of:

      - coils of successively superimposed layers, or
      - straight lengths, which if of a thickness less than 4.75 mm are of a width measuring at least ten times the thickness or if of a thickness of 4.75 mm or more are of a width which exceeds 150 mm and measures at least twice the thickness.
      Flat-rolled products include those with patterns in relief derived directly from rolling (for example, grooves, ribs, chequers, tears, buttons, lozenges) and those which have been perforated, corrugated or polished, provided that they do not thereby assume the character of articles or products of other headings.
      Flat-rolled products of a shape other than rectangular or square, of any size, are to be classified as products of a width of 600 mm or more, provided that they do not assume the character of articles or products of other headings.
      (l) Bars and rods, hot-rolled, in irregularly wound coils
      Hot-rolled products in irregularly wound coils, which have a solid cross-section in the shape of circles, segments of circles, ovals, rectangles (including squares), triangles or other convex polygons (including "flattened circles" and "modified rectangles", of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). These products may have indentations, ribs, grooves or other deformations produced during the rolling process (reinforcing bars and rods).
      (m) Other bars and rods
      Products which do not conform to any of the definitions at (ij), (k) or (l) above or to the definition of wire, which have a uniform solid cross-section along their whole length in the shape of circles, segments of circles, ovals, rectangles (including squares), triangles or other convex polygons (including "flattened circles" and "modified rectangles", of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). These products may:
      - have indentations, ribs, grooves or other deformations produced during the rolling process (reinforcing bars and rods);
      - be twisted after rolling.
      (n) Angles, shapes and sections
      Products having a uniform solid cross-section along their whole length which do not conform to any of the definitions at (ij), (k), (l) or (m) above or to the definition of wire.
      Chapter 72 does not include products of 7301 or 7302.
      (o) Wire
      Cold-formed products in coils, of any uniform solid cross-section along their whole length, which do not conform to the definition of flat-rolled products.
      (p) Hollow drill bars and rods
      Hollow bars and rods of any cross-section, suitable for drills, of which the greatest external dimension of the cross-section exceeds 15 mm but does not exceed 52 mm, and of which the greatest internal dimension does not exceed one half of the greatest external dimension. Hollow bars and rods of iron or steel not conforming to this definition are to be classified in 7304.


    2. Ferrous metals clad with another ferrous metal are to be classified as products of the ferrous metal predominating by weight.


    3. Iron or steel products obtained by electrolytic deposition, by pressure casting or by sintering are to be classified, according to their form, their composition and their appearance, in the headings of this Chapter appropriate to similar hot-rolled products.


    SUBHEADING NOTES

    1. In this Chapter the following have the meanings hereby assigned to them:
      (a) Alloy pig iron
      Pig iron containing, by weight, one or more of the following elements in the specified proportions:
      - more than 0.2% of chromium
      - more than 0.3% of copper
      - more than 0.3% of nickel
      - more than 0.1% of any of the following elements: aluminium, molybdenum, titanium, tungsten (wolfram), vanadium.
      (b) Non-alloy free-cutting steel
      Non-alloy steel containing, by weight, one or more of the following elements in the specified proportions:
      - 0.08% or more of sulphur
      - 0.1% or more of lead
      - more than 0.05% of selenium
      - more than 0.01% of tellurium
      - more than 0.05% of bismuth.
      (c) Silicon-electrical steel
      Alloy steels containing by weight at least 0.6% but not more than 6% of silicon and not more than 0.08% of carbon.They may also contain by weight not more than 1% of aluminium but no other element in a proportion that would give the steel the characteristics of another alloy steel.
      (d) High speed steel
      Alloy steels containing, with or without other elements, at least two of the three elements molybdenum, tungsten and vanadium with a combined content by weight of 7% or more, 0.6% or more of carbon and 3 to 6% of chromium.
      (e) Silico-manganese steel
      Alloy steels containing by weight:
      - not more than 0.7% of carbon,
      - 0.5% or more but not more than 1.9% of manganese, and
      - 0.6% or more but not more than 2.3% of silicon, but no other element in a proportion that would give the steel the characteristics of another alloy steel.


    2. For the classification of ferro-alloys in the subheadings of 7202 the following should be observed:

    A ferro-alloy is considered as binary and classified under the subheading (if it exists) if only one of the alloy elements exceeds the minimum percentage laid down in Chapter Note 1(c): by analogy, it is considered respectively as ternary or quaternary if two or three alloy elements exceed the minimum percentage.

    For the application of this Note the unspecified "other elements" referred to in Chapter Note 1(c) must each exceed 10% by weight.


    ADDITIONAL NOTE

    1. Throughout this Classification "high alloy steel" means alloy steels containing by weight one or more of the following elements in the proportion shown:

    - 2% or more of manganese

    - 2% or more of silicon

    - 0.5% or more of nickel

    - 1% or more of chromium

    - 0.1% or more of molybdenum

    - 0.1% or more of vanadium

    - 0.3% or more of tungsten

    - 0.3% or more of cobalt

    - 0.8% or more of copper

    - 0.1% or more of any other alloy element not being lead, phosphorus, sulphur, aluminium or carbon..

    SECTION 15 - BASE METALS AND ARTICLES OF BASE METAL
    CHAPTER 72 - IRON AND STEEL

    NOTE: For goods exempt from Export Entry, refer to Explanatory Notes, 1.5 Instructions for Completing an Export Entry.



    Heading no
    HS
    code
    Export Statistical
    Item
    Unit of quantity
      Description
      SUB-CHAPTER 01 - PRIMARY MATERIALS; PRODUCTS IN GRANULAR OR POWDER FORM

    7201
      PIG IRON AND SPIEGELEISEN IN PIGS, BLOCKS OR OTHER PRIMARY FORMS:

      7201.10
      7201.10.00
      T
      - Non-alloy pig iron containing by weight 0.5% or less of phosphorus phosphorus

      7201.20
      7201.20.00
      T
      - Non-alloy pig iron containing by weight more than 0.5% of phosphorus

      7201.50
      7201.50.00
      T
      - Alloy pig iron; spiegeleisen

    7202
      FERRO-ALLOYS:

      7202.1
      - Ferro-manganese:

      7202.11
      7202.11.00
      T
      -- Containing by weight more than 2% of carbon

      7202.19
      7202.19.00
      T
      -- Other

      7202.2
      - Ferro-silicon:

      7202.21
      7202.21.00
      T
      -- Containing by weight more than 55% of silicon

      7202.29
      7202.29.00
      T
      -- Other

      7202.30
      7202.30.00
      T
      - Ferro-silico-manganese

      7202.4
      - Ferro-chromium:

      7202.41
      7202.41.00
      T
      -- Containing by weight more than 4% of carbon

      7202.49
      7202.49.00
      T
      -- Other

      7202.50
      7202.50.00
      T
      - Ferro-silico-chromium

      7202.60
      7202.60.00
      T
      - Ferro-nickel

      7202.70
      7202.70.00
      T
      - Ferro-molybdenum

      7202.80
      7202.80.00
      T
      - Ferro-tungsten and ferro-silico-tungsten

      7202.9
      - Other:

      7202.91
      7202.91.00
      T
      -- Ferro-titanium and ferro-silico-titanium

      7202.92
      7202.92.00
      T
      -- Ferro-vanadium

      7202.93
      7202.93.00
      T
      -- Ferro-niobium

      7202.99
      7202.99.00
      T
      -- Other

    7203
      FERROUS PRODUCTS OBTAINED BY DIRECT REDUCTION OF IRON ORE AND OTHER SPONGY FERROUS PRODUCTS, IN LUMPS, PELLETS OR SIMILAR FORMS; IRON HAVING A MINIMUM PURITY BY WEIGHT OF 99.94%, IN LUMPS, PELLETS OR SIMILAR FORMS:

      7203.10
      7203.10.00
      T
      - Ferrous products obtained by direct reduction of iron ore

      7203.90
      7203.90.00
      T
      - Other

    7204
      FERROUS WASTE AND SCRAP; REMELTING SCRAP INGOTS OF IRON OR STEEL:

      7204.10
      7204.10.00
      T
      - Waste and scrap of cast iron

      7204.2
      - Waste and scrap of alloy steel:

      7204.21
      7204.21.01
      T
      -- Of stainless steel

      7204.29
      7204.29.12
      T
      -- Other

      7204.30
      7204.30.01
      T
      - Waste and scrap of tinned iron or steel

      7204.4
      - Other waste and scrap:

      7204.41
      7204.41.00
      T
      -- Turnings, shavings, chips, milling waste, sawdust, filings, trimmings and stampings, whether or not in bundles

      7204.49
      7204.49.01
      T
      -- Other

      7204.50
      7204.50.00
      T
      - Remelting scrap ingots

    7205
      GRANULES AND POWDERS, OF PIG IRON, SPIEGELEISEN, IRON OR STEEL:

      7205.10
      7205.10.00
      T
      - Granules

      7205.2
      - Powders:

      7205.21
      7205.21.00
      T
      -- Of alloy steel

      7205.29
      7205.29.00
      T
      -- Other
      SUB-CHAPTER 02 - IRON AND NON-ALLOY STEEL

    7206
      IRON AND NON-ALLOY STEEL IN INGOTS OR OTHER PRIMARY FORMS (EXCLUDING IRON OF 7203):

      7206.10
      7206.10.00
      T
      - Ingots

      7206.90
      7206.90.00
      T
      - Other

    7207
      SEMI-FINISHED PRODUCTS OF IRON OR NON-ALLOY STEEL:

      7207.1
      - Containing by weight less than 0.25% of carbon:

      7207.11
      7207.11.00
      T
      -- Of rectangular (including square) cross-section, the width measuring less than twice the thickness

      7207.12
      7207.12.00
      T
      -- Other, of rectangular (other than square) cross-section

      7207.19
      7207.19.00
      T
      -- Other

      7207.20
      7207.20.00
      T
      - Containing by weight 0.25% or more of carbon

    7208
      FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE, HOT-ROLLED, NOT CLAD, PLATED OR COATED:

      7208.1
      - In coils, not further worked than hot-rolled, of a thickness of less than 3 mm and having a minimum yield point of 275 MPa, or of a thickness of 3 mm or more and having a minimum yield point of 355 MPa:

      7208.10
      7208.10.00
      T
      -- In coils, not further worked than hot-rolled, with pattern in relief

      7208.2
      - Other, in coils, not further worked than hot-rolled, pickled:

      7208.25
      7208.25.00
      T
      -- Of a thickness of 4.75 mm or more

      7208.26
      7208.26.00
      T
      -- Of a thickness of 3 mm or more but less than 4.75 mm

      7208.27
      7208.27.00
      T
      -- Of a thickness of less than 3 mm

      7208.3
      - Other, in coils, not further worked than hot-rolled:

      7208.36
      7208.36.00
      T
      -- Of a thickness exceeding 10 mm

      7208.37
      7208.37.00
      T
      -- Of a thickness of 4.75 mm or more but not exceeding 10 mm

      7208.38
      7208.38.00
      T
      -- Of a thickness of 3 mm or more but less than 4.75 mm

      7208.39
      7208.39.00
      T
      -- Of a thickness of less than 3 mm

      7208.4
      - Other, not in coils, not further worked than hot-rolled:

      7208.40
      7208.40.00
      T
      -- Not in coils, not further worked than hot-rolled, with patterns in relief

      7208.5
      - Other, not in coils, not further worked than hot-rolled:

      7208.51
      7208.51.00
    		T
      -- Of a thickness exceeding 10 mm
      7208.52
      7208.52.00
    		T
      -- Of a thickness of 4.75 mm or more but not exceeding 10 mm
      7208.53
      7208.53.00
      T
      -- Of a thickness of 3 mm or more but less than 4.75 mm
      7208.54
      7208.54.00
      T
      -- Of a thickness of less than 3 mm
      7208.90
      7208.90.50
      T
      - Other
    7209
      FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE, COLD-ROLLED (COLD-REDUCED), NOT CLAD, PLATED OR COATED:
      7209.1
      - In coils, not further worked than cold-rolled (cold-reduced):
      7209.15
      7209.15.00
      T
      -- Of a thickness of 3 mm or more
      7209.16
      7209.16.00
      T
      -- Of a thickness exceeding 1 mm but less than 3 mm
      7209.17
      7209.17.00
      T
      -- Of a thickness of 0.5 mm or more but not exceeding 1 mm
      7209.18
      7209.18.00
      T
      -- Of a thickness of less than 0.5 mm
      7209.2
      - Not in coils, not further worked than cold-rolled (cold-reduced):
      7209.25
      7209.25.00
      T
      -- Of a thickness of 3 mm or more
      7209.26
      7209.26.00
      T
      -- Of a thickness exceeding 1 mm but less than 3 mm
      7209.27
      7209.27.00
      T
      -- Of a thickness of 0.5 mm or more but not exceeding 1 mm
      7209.28
      7209.28.00
      T
      -- Of a thickness of less than 0.5 mm
      7209.90
      7209.90.00
      T
      - Other
    7210
      FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE, CLAD, PLATED OR COATED:
      7210.1
      - Plated or coated with tin:
      7210.11
      7210.11.00
      T
      -- Of a thickness of 0.5 mm or more
      7210.12
      7210.12.00
      T
      -- Of a thickness of less than 0.5 mm
      7210.20
      7210.20.00
      T
      - Plated or coated with lead, including terne-plate
      7210.30
      7210.30.00
      T
      - Electrolytically plated or coated with zinc
      7210.4
      - Otherwise plated or coated with zinc:
      7210.41
      7210.41.00
      T
      -- Corrugated
      7210.49
      7210.49.00
      T
      -- Other
      7210.50
      7210.50.00
      T
      - Plated or coated with chromium oxides or with chromium and chromium oxides
      7210.6
      - Plated or coated with aluminium:
      7210.61
      7210.61.00
      T
      -- Plated or coated with aluminium-zinc alloys
      7210.69
      7210.69.00
      T
      -- Other
      7210.70
      7210.70.00
      T
      - Painted, varnished or coated with plastics
      7210.90
      7210.90.00
      T
      - Other
    7211
      FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF LESS THAN 600 MM, NOT CLAD, PLATED OR COATED:
      7211.1
      - Not further worked than hot-rolled:
      7211.13
      7211.13.00
      T
      -- Rolled on four faces or in a closed box pass, of a width exceeding 150 mm and a thickness of not less than 4 mm, not in coils and without patterns in relief

      7211.14
      7211.14.00
      T
      -- Other, of a thickness of 4.75 mm or more
      7211.19
      7211.19.91
      T
      -- Other
      7211.2
      - Not further worked than cold-rolled (cold-reduced):
      7211.23
      7211.23.00
      T
      -- Containing by weight less than 0.25% of carbon
      7211.29
      7211.29.00
      T
      -- Other
      7211.90
      7211.90.00
      T
      - Other
    7212
      FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF LESS THAN 600 MM, CLAD, PLATED OR COATED:

      7212.10
      7212.10.00
      T
      - Plated or coated with tin
      7212.20
      7212.20.00
      T
      - Electrolytically plated or coated with zinc
      7212.30
      7212.30.00
      T
      - Otherwise plated or coated with zinc
      7212.40
      7212.40.00
      T
      - Painted, varnished or coated with plastics
      7212.50
      7212.50.00
      T
      - Otherwise plated or coated
      7212.60
      7212.60.00
      T
      - Clad
    7213
      BARS AND RODS, HOT-ROLLED, IN IRREGULARLY WOUND COILS, OF IRON OR NON-ALLOY STEEL:
      7213.10
      7213.10.01
      T
      - Containing indentations, ribs, grooves or other deformations produced during the rolling process
      7213.20
      7213.20.01
      T
      - Other, of free-cutting steel
      7213.9
      - Other:
      7213.91
      7213.91.00
      T
      -- Of circular cross-section measuring less than 14 mm in diameter
      7213.99
      7213.99.00
      T
      -- Other
    7214
      OTHER BARS AND RODS OF IRON OR NON-ALLOY STEEL, NOT FURTHER WORKED THAN FORGED, HOT-ROLLED, HOT-DRAWN OR HOT-EXTRUDED, BUT INCLUDING THOSE TWISTED AFTER ROLLING:

      7214.10
      7214.10.01
      T
      - Forged
      7214.20
      7214.20.01
      T
      - Containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling
      7214.30
      7214.30.01
      T
      - Other, of free-cutting steel
      7214.9
      - Other:
      7214.91
      7214.91.00
      T
      -- Of rectangular (other than square) cross-section
      7214.99
      7214.99.00
      T
      -- Other
    7215
      OTHER BARS AND RODS OF IRON OR NON-ALLOY STEEL:
      7215.10
      7215.10.01
      T
      - Of free-cutting steel, not further worked than cold-formed or cold-finished
      7215.50
      7215.50.00
      T
      - Other, not further worked than cold-formed or cold-finished
      7215.90
      7215.90.01
      T
      - Other
    7216
      ANGLES, SHAPES AND SECTIONS OF IRON OR NON-ALLOY STEEL:
      7216.10
      7216.10.00
      T
      - U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm

      7216.2
      - L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm:
      7216.21
      7216.21.00
      T
      -- L sections
      7216.22
      7216.22.00
      T
      -- T sections
      7216.3
      - U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded of a height of 80 mm or more:
      7216.31
      7216.31.00
      T
      -- U sections
      7216.32
      7216.32.00
      T
      -- I sections
      7216.33
      7216.33.00
      T
      -- H sections
      7216.40
      7216.40.00
      T
      - L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more
      7216.50
      7216.50.00
      T
      - Other angles, shapes and sections, not further worked than hot-rolled, hot-drawn or extruded
      7216.6
      - Angles, shapes and sections, not further worked than cold-formed or cold-finished
      :
      7216.61
      7216.61.00
      T
      -- Obtained from flat-rolled products
      7216.69
      7216.69.00
      T
      -- Other
      7216.9
      - Other:
      7216.91
      7216.91.00
      T
      -- Cold-formed or cold-finished from flat-rolled products
      7216.99
      7216.99.00
      T
      -- Other
    7217
      WIRE OF IRON OR NON-ALLOY STEEL:
      7217.10
      7217.10.00
      T
      - Not plated or coated, whether or not polished
      7217.20
      7217.20.00
      T
      - Plated or coated with zinc
      7217.30
      7217.30.00
      T
      - Plated or coated with other base metals
      7217.90
      7217.90.00
      T
      - Other
      SUB-CHAPTER 03 - STAINLESS STEEL
    7218
      STAINLESS STEEL IN INGOTS OR OTHER PRIMARY FORMS; SEMI-FINISHED PRODUCTS OF STAINLESS STEEL:
      7218.10
      7218.10.00
      T
      - Ingots and other primary forms
      7218.9
      - Other:
      7218.91
      7218.91.00
      T
      -- Of rectangular (other than square) cross-section
      7218.99
      7218.99.00
      T
      -- Other
    7219
      FLAT-ROLLED PRODUCTS OF STAINLESS STEEL, OF A WIDTH OF 600 MM OR MORE:
      7219.1
      - Not further worked than hot-rolled, in coils:
      7219.11
      7219.11.00
      T
      -- Of a thickness exceeding 10 mm
      7219.12
      7219.12.00
      T
      -- Of a thickness of 4.75 mm or more but not exceeding 10 mm
      7219.13
      7219.13.00
      T
      -- Of a thickness of 3 mm or more but less than 4.75 mm
      7219.14
      7219.14.00
      T
      -- Of a thickness of less than 3 mm
      7219.2
      - Not further worked than hot-rolled, not in coils:
      7219.21
      7219.21.00
      T
      -- Of a thickness exceeding 10 mm
      7219.22
      7219.22.00
      T
      -- Of a thickness of 4.75 mm or more but not exceeding 10 mm
      7219.23
      7219.23.00
      T
      -- Of a thickness of 3 mm or more but less than 4.75 mm
      7219.24
      7219.24.00
      T
      -- Of a thickness of less than 3 mm
      7219.3
      - Not further worked than cold-rolled (cold-reduced):
      7219.31
      7219.31.00
      T
      -- Of a thickness of 4.75 mm or more
      7219.32
      7219.32.00
      T
      -- Of a thickness of 3 mm or more but less than 4.75 mm
      7219.33
      7219.33.00
      T
      -- Of a thickness exceeding 1 mm but less than 3 mm
      7219.34
      7219.34.00
      T
      -- Of a thickness of 0.5 mm or more but not exceeding 1 mm
      7219.35
      7219.35.00
      T
      -- Of a thickness of less than 0.5 mm
      7219.90
      7219.90.00
      T
      - Other
    7220
      FLAT-ROLLED PRODUCTS OF STAINLESS STEEL, OF A WIDTH OF LESS THAN 600 MM:
      7220.1
      - Not further worked than hot-rolled:
      7220.11
      7220.11.00
      T
      -- Of a thickness of 4.75 mm or more
      7220.12
      7220.12.00
      T
      -- Of a thickness of less than 4.75 mm
      7220.20
      7220.20.00
      T
      - Not further worked than cold-rolled (cold-reduced)
      7220.90
      7220.90.00
      T
      - Other
    7221
      7221.00
      7221.00.01
      T
      BARS AND RODS, HOT-ROLLED, IN IRREGULARLY WOUND COILS, OF STAINLESS
      STEEL
    7222
      OTHER BARS AND RODS OF STAINLESS STEEL; ANGLES, SHAPES AND SECTIONS OF STAINLESS STEEL:
      7222.1
      - Bars and rods, not further worked than hot-rolled, hot-drawn or extruded:
      7222.11
      7222.11.00
      T
      -- Of circular cross-section
      7222.19
      7222.19.00
      T
      -- Other
      7222.20
      7222.20.01
      T
      - Bars and rods, not further worked than cold-formed or cold-finished
      7222.30
      7222.30.01
      T
      - Other bars and rods
      7222.40
      7222.40.01
      T
      - Angles, shapes and sections
    7223
      7223.00
      7223.00.00
      T
      WIRE OF STAINLESS STEEL
      SUB-CHAPTER 04 - OTHER ALLOY STEEL; HOLLOW DRILL BARS AND RODS, OF ALLOY OR NON-ALLOY STEEL
    7224
      OTHER ALLOY STEEL IN INGOTS OR OTHER PRIMARY FORMS; SEMI-FINISHED PRODUCTS OF OTHER ALLOY STEEL:
      7224.10
      7224.10.01
      T
      - Ingots and other primary forms
      7224.90
      7224.90.01
      T
      - Other
    7225
      FLAT-ROLLED PRODUCTS OF OTHER ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE:
      7225.1
      - Of silicon-electrical steel:
      7225.11
      7225.11.00
      T
      -- Grain-oriented
    7225.19
      7225.19.00
      T
      -- Other
      7225.20
      7225.20.00
      T
      - Of high speed steel
      7225.30
      7225.30.00
      T
      - Other, not further worked than hot-rolled, in coils
      7225.40
      7225.40.00
      T
      - Other, not further worked than hot-rolled, not in coils

    7225.50
      7225.50.00
      T
      - Other, not further worked than cold-rolled (cold-reduced)
    7225.9
      - Other:
    7225.91
      7225.91.00
      T
      -- Electrolytically plated or coated with zinc
    7225.92
      7225.92.00
      T
      -- Otherwise plated or coated with zinc
    7225.99
      7225.99.00
      T
      -- Other
    7226
      FLAT-ROLLED PRODUCTS OF OTHER ALLOY STEEL, OF A WIDTH OF LESS THAN 600 MM:
    7226.1
      - Of silicon-electrical steel:
    7226.11
      7226.11.00
      T
      -- Grain-oriented
    7226.19
      7226.19.00
      T
      -- Other
    7226.20
      7226.20.00
      T
      - Of high speed steel
    7226.9
      - Other:
    7226.91
      7226.91.00
      T
      -- Not further worked than hot-rolled
    7226.92
      7226.92.00
      T
      -- Not further worked than cold-rolled (cold-reduced)
    7226.93
      7226.93.00
      T
      -- Electrolytically plated or coated with zinc
    7226.94
      7226.94.00
      T
      -- Otherwise plated or coated with zinc
    7226.99
      7226.99.01
      T
      -- Other
    7227
      BARS AND RODS, HOT-ROLLED, IN IRREGULARLY WOUND COILS, OF OTHER ALLOY STEEL:
    7227.10
      7227.10.01
      T
      - Of high speed steel
    7227.20
      7227.20.01
      T
      - Of silico-manganese steel
    7227.90
      7227.90.00
      T
      - Other
    7228
      OTHER BARS AND RODS OF OTHER ALLOY STEEL; ANGLES, SHAPES AND SECTIONS, OF OTHER ALLOY STEEL; HOLLOW DRILL BARS AND RODS, OF ALLOY OR NON-ALLOY STEEL:
    7228.10
      7228.10.01
      T
      - Bars and rods, of high speed steel
    7228.20
      7228.20.01
      T
      - Bars and rods, of silico-manganese steel
    7228.30
      7228.30.01
      T
      - Other bars and rods, not further worked than hot-rolled, hot-drawn or extruded
    7228.40
      7228.40.01
      T
      - Other bars and rods, not further worked than forged
    7228.50
      7228.50.00
      T
      - Other bars and rods, not further worked than cold-formed or cold-finished
    7228.60
      7228.60.01
      T
      - Other bars and rods
    7228.70
      7228.70.01
      T
      - Angles, shapes and sections
    7228.80
      7228.80.00
      T
      - Hollow drill bars and rods
    7229
      WIRE OF OTHER ALLOY STEEL:
    7229.10
      7229.10.00
      T
      - Of high speed steel
    7229.20
      7229.20.01
      T
      - Of silico-manganese steel
    7229.90
      7229.90.00
      T
      - Other


    ISSUE DATE: 1 JANUARY 2002



    Previous PageNext Page